Tag Archives: belt loops

OAL2018: Belt Loops & Waistband

18 Jun

Good morning, everyone! If you are participating in this year’s OAL, you should be rocking and rolling along with both your sewing & knitting projects. As I mentioned in the announcement, I will not be offering full tutorials for sewing the Lander Pants – there is a great sewalong available for free on the True Bias website, should you need the additional support – but I did want to pop in and share an alternate method for sewing the belt loops & attaching the waistband. Even if you are not participating in this year’s OAL, I hope you will find this useful!

OAL 2018: Belt Loops & Waistband

You’ll want to make your belt loops before you attach the waistband (note that you can also attach the belt loops after the waistband if you prefer! For the sake of simplicity, I am following the pattern directions here). The pattern has you sew a tube that you turn right side out and press flat. This is a great method if you are sewing with a lightweight fabric, but it can be a nightmare to try to turn that skinny tube if you are using a heavier fabric, especially denim. Even my red linen doesn’t like being pulled like that! So here is an alternate method if you are using a thicker fabric, or just hate turning tubes 🙂

OAL 2018: Belt Loops & Waistband

Finish one long edge of the belt loop piece. I used a serger, but you can also sew over the edge with a zigzag stitch, or bind with fabric.

OAL 2018: Belt Loops & Waistband

The pattern is designed for the finished belt loops to be about 1/2″ wide. You may want to trim 1/8″ off the long (unfinished) edge of your piece if you want to maintain that measurement. Otherwise, your belt loops will end up being about 5/8″ wide.

OAL 2018: Belt Loops & Waistband
OAL 2018: Belt Loops & Waistband

Starting with the unfinished side, fold the belt loop into thirds with the right sides facing. You will end with the finished edge on top, hiding all raw edges. Be nitpicky here and do your best to get the finished edge right EXACTLY on top of the first fold.

OAL 2018: Belt Loops & Waistband

Topstitch along both long sides at 1/8″. This is why it is so important to get the finished edge right on the fold – if you are too close to the center, the stitching line won’t catch it.

And that’s it! This gives the same effect as the turned-tube-belt-loop-, but I find it a lot easier to sew. From here, you can cut your belt loop into 5 pieces and attach them to the top of the pants as instructed.

Now, for the waistband!

If this tutorial seems like deja vu, it’s because I’ve showed it before on my blog! I wanted to show it again for those who missed it the first time, and also to show that it does work for one piece waistbands as well as two piece!

OAL 2018: Belt Loops & Waistband

On your interfaced waistband piece, fold up one long edge a little bit less than the seam allowance (this pattern is 1/2″, so I folded up my edge at 3/8″) and press.

OAL 2018: Belt Loops & Waistband

This is gonna seem ass-backwards – just bear with me! Attach the waistband to the INSIDE of the pants, with the right side of the waistband facing the wrong side of the pants. Sew all the way around at your normal seam allowance, making sure to leave at least 1/2″ overhang at each end (you can always cut off any excess). You will sew all the way around, from one opening to the other. If your pants have a zipper, make sure that it is unzipped and sew right across the zipper – just go slow so you don’t break your needle on the teeth.

OAL 2018: Belt Loops & Waistband

Now you’ll fold the waistband back on itself, with the right sides facing. The side that has been folded and pressed – i.e., the side that was not sewn to the pants) should hang below by about 1/8″-1/16″. This is to ensure that the stitching line you just did will be covered when you turn the waistband right side out.

Now, stitch along the short edge, keeping in line with the center front edge of the pants. It may be helpful to draw a guideline here first with a ruler (which is exactly what I do – no shame here!).

OAL 2018: Belt Loops & Waistband

Trim one of the seam allowance layers in half. Do not trim the corner, keep some seam allowance there.

OAL 2018: Belt Loops & Waistband

Now you will turn the waistband right side out! To get a nice, crisp corner, start by sticking your thumb in the waistband up to the corner.

OAL 2018: Belt Loops & Waistband

While your thumb is still in that corner, use your pointer finger to push the seam allowance down to one side (doesn’t matter which side) (Sorry, I don’t have pretty hands haha)

OAL 2018: Belt Loops & Waistband
OAL 2018: Belt Loops & Waistband

Keeping your fingers in that weird pinch, turn the waistband out to the right side.

OAL 2018: Belt Loops & Waistband

You should end up with a nice sharp corner here! You can use a point turner to really push the edge out if you need it to be even sharper 🙂 By holding the seam allowances in place when you turn right side out, this keeps the corner sharp (rather than trying to crap the seam allowances in after the fact). Keeping a bit of fabric in the seam allowances (rather than trimming down aggressively) also adds some structure to that corner, so it doesn’t collapse on itself.

OAL 2018: Belt Loops & Waistband

Finally, you can pin the remainder of your waistband down and topstitch from the right side, making sure to cover the first stitching line. I like to start at the center back and go all the way around the long rectangle, ending where I started. You can then cover the backstitching with a belt loop 🙂

OAL 2018: Belt Loops & Waistband

And that’s it! I love this method for attaching a waistband, because it ensures you get a beautiful, even topstitch on the outside without having to worry about catching the facing on the inside! It’s just EASY and basically fool-proof! You can also use this method for sewing in the round waistbands, cuffs (buttoned or in the round) and even collar stands.

Let me know if you have any questions!

Advertisements